Home Distributors/Dealers Case Drawing Products Specials Brochure Order Support Contact Us Join Mail List

Click here for: Compact D60 depth sounder

D110 1000' DSP Depth Sounder

Download User's Manual PDF

D110 1000' DSP Depthsounder

CE Certified for Europe

CE Certified

Waterproof front case


Operating Voltage:
9.50 - 16.00 VDC

Current Drain:
0.035 amps nominal

Operating Temperature:
32 to 122 deg F (0 to 50 C)

Large 4 digit LCD, 5 levels of backlighting with external backlight on/off control

Display Data:
Shallow Alarm
Deep Alarm
Keel Offset
Feet, Meters, Fathoms

1.2 to 1000+ feet (in tenths below 20.0)
0.4 to 365+ meters (in tenths below 20.0)
0.2 to 167+ fathoms (in tenths below 20.0)

Data Ouput:
NMEA 0183 serial 4800 BAUD, $SDDPT
Programmable as an external alarm output

Built-in 85 dB audible alarm. Settable shallow, deep and anchor drag alarms.

4.3" x 4.3" (110m x 110mm)

2-1/8" (54mm) round hole


The D110 Digital DSP depth sounder uses Digital Signal Processing (DSP) to reliably display water depth from 1.2 foot (0.4 Metre) to 1000+ feet (365 Metres). Depth can be displayed in feet, meters or fathoms. Variable display damping is provided so the user can optimize response speed against display stability (averaging).

The D110 has programmable shallow, deep and anchor drag alarms built-in and can display the depth in feet, metres or fathoms. A keel offset from -20.0 to +20.0 feet can be entered so the D110 shows the depth below the surface, below the keel or below the transducer. The alarm values and keel offset are automatically converted if the units of measure are changed between feet, meters and fathoms.

The D110 uses Digital Signal Processing (DSP) to enable sensitivity never before found in such a low cost sounder like the D110. The DSP also provides superior high speed rejection of false signals due to transducer slap (buffeting), surface turbulence, thermoclines, double bounce and is almost immune to other depth sounders and fishfinders operating near-by.

Five levels of backlighting can be selected for night-time viewing. The backlights can be turned ON and OFF remotely. All set-up constants are saved in a non-volatile memory.

The D110 outputs depth and keel offset as a standard NMEA $SDDPT sentence on NMEA 0183 serial data line at 4800 BAUD. This ASCII information can be used to log performance, repeat the display information at a remote location (see www.cruzpro.com/rp30.html and www.cruzpro.com/rp110.html). If NMEA 0183 serial data is not required, then the output terminal can be programmed as an external alarm output pin.

Both through-hull and transom mount transducers are available separately for the D110.

D110 Wiring Diagram

D110 Connection Diagram

Connecting the CruzPro ER-1 External Relay module to the NMEA 0183/External Alarm Output

Click here to go to ER-1 page

ER-1 External Relay Connection Diagram

D110 Transducer Options (Available separately):

THD-2 Plastic Thru Hull Transducer
THD-2 Thru-hull plastic transducer
THD-2 Dimensions
THD-2 Thru-hull plastic transducer

TMD-2 Transom Mount Transducer
TMD-2 Transom mount transducer
TMD-2 Dimensions
TMD-2 Transom mount transducer dimensions
THD-4 Bronze Thru Hull Transducer THD-4 Bronze thru-hull transducer
THD-4 Dimensions
THD-4 bronze transducer dimensions

THD-5 Long Stem Bronze Thru Hull Transducer
THD-5 long stem bronze thru-hull transducer
THD-5 Dimensions THD-5 long stem bronze transducer dimensions

Home Distributors/Dealers Case Drawing Products Specials Brochure Order Support Contact Us Join Mail List